youyeetoo NanoPi R5S Mini Router with Metal Case,4GB LPDDR4 16GB EMMC, RK3568 Development Board 0.8TOPS NPU Support Docker Three Ethernet Ports USB3.0 HDMI Support M.2 NVMe PD Power (Power Bundle)

Product Information

Being able to power this with USB is a huge bonus, since I can power it with a USB battery bank to keep it online during power outages much longer than my UPS which generally lasts only 20 minutes. g. MTK MT7662) work in CD-ROM mode by default and need to be switched by usb_modeswitch, you can try to add usb_modeswitch configuration to the following directory: /etc/usb_modeswitch. One of the four rear leds is flashing (sys) – the others are WAN, LAN 1 and 2 LAN2 (The connector marked WAN is Gbps speed, the two LAN ports are 2. That leads me to believe the DHCP requests are getting swallowed/not forwarded by NanoPi for some reason.

Es hat mich sehr gefreut, dass das Gerät bei einer Gigabit-Internetverbindung keine Bottleneck hat, was ein großes Plus ist. Just a quick note: Like the R4S before it (and that’s where the similarity ends), the R5S gets quite hot in operation – so not a good idea to put anything on top of it.It seems that in FriendlyWrt LUCI menu, under SYSTEM, eMMC tools it is easy to tranfer that back to eMMC – not that I want to right now, but nice to know. FriendlyELEC NanoPi R5S single-board computer (SBC) measures 90 x 62mm, slightly larger than the Raspberry Pi 4 Model B, which measures 3.

The system performs at its maximum advertised frequency during the test, and I don’t any obvious bottleneck shere. ports : 2 Ethernet 5Gbit ports : - Ethernet 10Gbit ports : - SFP ports : - SFP+ ports : - VLAN : Yes Modem : - Comments network ports : 1G x1 (RTL8211F-CG), 2. At this point the laptop and mini PC should get their IP address from NanoPi R5S on the respective subnets. The HDMI output is touted as handling 4096*2034 resolution, not much use if the software can’t keep up) and I could get no sound at all on Android despite testing on two monitors and with two different HDMI leads. I found it hard to measure consumption with more complex scenarios just with a primitive meter only outputting actual amps/volts.aarch64 /aarch64-cortexa53-linux-gnu /sysroot --enable-languages=c, c++ --enable-fix-cortex-a53-843419 --with-arch=armv8-a+crypto+crc --with-cpu=cortex-a53 --with-pkgversion=ctng-1. But if someone intends to run a server both questioning the numbers and switching to a better benchmarking mode is a great idea.

Ok, based on A55 with ARMv8 Crypto Extensions formula now we know that the CPU cores clock at ~1840 MHz with the FriendlyWRT image. Can anyone recommend what else can I check to make the laptop reach the public internet (I’m not sure if I’m supposed to have 1 or 2 subnets for instance)? sh show the processor runs at 1992 MHz (or 1845 MHz real), and again the 25% IRQ should mean one core is fully utilized to handle IRQs. The trick in my case was to remove the bridge0 interface between eth1 and eth2, and use these interfaces individually. They’re sufficient for a desktop machine but generally speaking when you need to get performance for routing or for TCP processing, you quickly measure the difference with more serious (but more expensive) chips.HOWEVER, after borrowing the WIFI remote control from my normal TV box, I went about testing Android – meanwhile back in Italy, Antonio was doing similar testing. This is useful to solder a pinheader and connect a USB-to-UART module to get the output for debugging. A microSD card socket can be found on one of the sides, while the rear panel comes with a USB-C port for power, a WiFi antenna hole (which can also be used to run cables for GPIO.

Major downside: you need a lot of patience since after adjusting settings it requires a long(er) time span for the new averaged consumption value to settle. Additionally make sure your User-Agent is not empty and is something unique and descriptive and try again.Some other detailed adjustments: Set time zone to Shanghai by default, remove lcd2usb, improve security settings, tune sysctl parameters, fix docker firewall settings, etc. If putting it on it makes ksoftirqd pop up, then they’re hindering each other, and you’d rather change the RPS setting to free another core and use it for iperf.