LTP Grimex - Heavy Duty Cleaner, Grease and Grime Remover 1 Litre

Product Information

During the installation process, dust, grime, and dirt can accumulate on the surface of your newly laid patio or driveway. Even though porcelain paving isn't porous, surface dirt can mix with grout and make your paving appear dull and dirty. I should have sought advice on day one ~ GRIMEX world like magic but doing a whole floor in one go has me beat. I do a section at a time and the results are fantastic. It's suitable for removing ingrained dirt, grease and grime, and can also be used to clean neglected areas or areas subject to wear and tear.

Intensive cleaner, effective for removing stains such as oil, grease, ingrained dirt, grime and old wax layers from all artificial and natural stone and tiles. Ideal for general stone care and for use in the restoration of artificial and natural tiles and floors. It is especially effective on stone, travertine, slate, terracotta, porcelain and quarry tiles. LTP Grimex helps remove stubborn stains and existing layers of sealant from floors and tiles. It is also suitable for the general maintenance cleaning of external driveways, patios and paths. Dilute the solution 1:1 with cool water. Mask up and protect any areas that are not going to be cleaned. So, now we know what porcelain slabs are, lets delve into the best ways to clean and care for your paving. We’ve offered care guidance for each stage of your paving installation project. How to care for outdoor paving before installation It may be tempting to use 10mm porcelain tiles for your external paving project, either because you like a particular design or colour, or the tiles are a lot lighter and easier to handle than purposeful 20mm outdoor porcelain paving. However, we recommend against using 10mm tiles for your external paving project. DON'T use it as a regular cleaner, follow the LTP instructions and you can restore a floor that you thought would never be clean.Leave the solution to penetrate the surface. Leave for 1-5 hours depending on the level of soiling. OMG ~ I did try the few drops to a gallon but soon resorted to neat with a yard broom to scrub. Four tiles at a time, work GRIMEX into the tiles and wait. Srub with a bit of water, scrub with more water, mop with a lot of water. Rinse and admire the result. After moving in to our new to us house the large extent of large yellowish tiles never looked clean. A cancellation request by the consumer must be put in writing to [email protected] and received by the Company within the 7 working day period. TIPS: LTP Grimex is effective at removing the seal from natural stone surfaces. After using LTP Grimex you may wish to re seal or enhance your surface using an appropriate sealing product.

If you’re wondering how to clean porcelain paving before grouting, we recommend using LTP Grimex. Simply dilute one-part LTP Grimex in ten parts warm water and apply it liberally over the entire surface of the slabs using a soft brush. For stubborn marks, use a stiff brush. After 5-10 minutes, rinse off thoroughly with clean water. Spread out evenly using a roller, sealer applicator, paintbrush or sprayer. Allow to dry for 30 minutes. Apply a second coat and leave to cure for a minimum of 1 hour before grouting.To use, carefully apply the solution to a pre-wet surface with a sponge or a mop, allow to sit for 3-5 minutes for cleaning, then scrub with a brush, sponge or nylon pad.It can require hard brushing, but once applied it is very fast-acting. I scrubbed by hand, I scrubbed with a yard broom, I even bought an industrial floor cleaner with the big pads. This beast turned cleaning into a wrestling match around the kitchen/dining room. Apply liberally, spreading over the surface of the tiles. If necessary, agitate with a scrubbing brush. This rapid-action cleaning agent is suitable for porcelain paving and can remove cement residues, grout stains, salts, efflorescence, and similar deposits. The best way to clean porcelain slabs:

Or if you’re considering an indoor installation, our guide on how to clean tiles before grouting features plenty of helpful advice. Leave to react for 5-10 minutes, keeping the surface wet with additional solution. Agitate surface again, mop up and rinse thoroughly with clean water. Important: - Test the solution on an inconspicuous area before general application. Any alkalinity remaining on surfaces treated with this product should be completely neutralised. Still featuring the original formulation, Grimex is designed for all types of natural and engineered stone and tile, from limestone and marble, to ceramic and porcelain. It can be used to remove residue before application of a sealer; to daily and deep clean surfaces and to renovate tiles in all environments, including historic settings. Looking after your porcelain paving will keep it in great condition for years to come, so we’ve collated our favourite products to help you care for your paving before and after installation.

Sorry

The manufacturer suggests that protective clothing, eyewear and gloves are worn and that it is to be kept out of the reach of children. If irritation occurs, it is advised that you seek medical advice or attention. LTP Grimexhas been short-listed as a finalist in Tomorrow’s Cleaning Awards 2024. For over a decade, the Tomorrow’s Cleaning Awards have been a celebration of the finest industry innovations and the best time-tested solutions that the cleaning and hygiene sector has to offer. Public voting will open in early January next year, with winners announced in March 2024. Before you use your grout cleaner for the first time, consider your own safety as well as the safety of anyone else in your house. Scrub using a short-haired stiff bristled brush. Rub the surface with a clean lint free-dry cloth to remove the softened films.