SONOFF Basic R2 10A Smart WiFi Wireless Light Switch, Universal DIY Module for Smart Home Automation Solution, Works with Amazon Alexa & Google Home, Compatible with IFTTT, No Hub Required

Product Information

Main switch for 4-channel pin, active low. APP configuration pin, when the low level> 5S, enter the pairing mode.

This item is suitable for use with single, double and triple kinetic switches plus a single switch key fob. WiFi and RF Wireless Receiver Non-Dimmable in Matt White - Specs The device obtains information in different ways in the two modes, read below section for details. 4.3 The Wi-Fi module basic workflow

SUBSCRIBE TO NEWSLETTER

Place the module’s power supply (VCC) pin capacitance and other module pin capacitances, resistors as close as possible to the module pins, and the tracepath should be short. Unregistered: The device has not been bound to account. The device needs to be bound to the eWeLink account to connect to the cloud server. You can bind the device by tap “Add Device” in the eWeLink APP. The flashing of the Wi-Fi status light is in a cycle of 2 seconds, as shown in the figure, the low-level light is on and the high-level light is off. Detailed explanation of each status:

PSF-B04 supports timer. The eWeLink APP provides four timing modes to facilitate the use in more scenarios.The switch for the third channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. No Server: The device has been connected to the router, but it cannot connect to the server (also known as”cannot access the Internet”).

The switch for the second channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. The switch for the fourth channel pin, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. This is the Forum CUL-40039 Culina Konect Wireless On/Off Kinetic Switch Non-Dimmable Wi-Fi Module - a wifi and RF wireless receiver. SONOFF SV is a low voltage switch. The low voltage light switch supports 5-24V power supply. Power supply separation enables it to control both AC and DC power, although some welding is required for this purpose. It has GIPO reserved to support secondary development. This product does not have 433 RF function and shell. The relay switch for the fourth channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. Note: The chip configuration pin needs to pull down (1~4.7K) resistor to ground.

Environmentally friendly

The compact design means it can be installed almost anywhere. It has a range of up to 40m from the switch when outside, or 8m away when indoors and can be controlled not only by the switches. PSF-B04 module can be used as a 4-channel switch, which can control the switch locally or remotely through APP. The flashing mode of the Wi-Fi status light on the device represents the its current network working status. The specific status includes the following seven types: Strong signal up to 40m range outdoors, 15m indoors for plasterboard, 8m indoors for concrete or glass External reset signal: active at low level, externally need to pull up a 10K resistor to 3.3V, and connect a 100nF capacitor to ground.

The 40039 is a single channel Wi-Fi relay switch receiver. Part of the Culina Konect system from Forum Lighting. This a completely wireless switching system converts the kinetic energy produced by physically switching the switch into electrical energy to control your lights via remote switch and receiver.This item works with Alexa and Google Assistant, and the manufacturer has their own app to control this system. The upper and lower layers of the PCB where the module is placed should not be routed as much as possible. Do the copper-clad processing, and the PCB from the module antenna to the nearest pin of the module should be hollowed out as much as possible. Power-on status configuration: The power-on switch status can be configured on or off through the APP, and the default power-on status is off. Count downtimer: The count down is to facilitate the user to perform one-time timing operations, such as turn on/off the device after 30 minutes. It is very convenient to turn off a device after running a period of time. This device supports up to 24 hours of count down.